英语翻译4.8 当某些舱位作为压载使用后,请立即关闭相关舱位的取样进口阀,并按下控制柜面板上相应舱位的“人工切断”按钮,取消对该舱位的自动取样；此时,相应检测舱位工作指示灯显示

英语翻译4.8 当某些舱位作为压载使用后,请立即关闭相关舱位的取样进口阀,并按下控制柜面板上相应舱位的“人工切断”按钮,取消对该舱位的自动取样；此时,相应检测舱位工作指示灯显示
英语翻译
4.8 当某些舱位作为压载使用后,请立即关闭相关舱位的取样进口阀,并按下控制柜面板上相应舱位的“人工切断”按钮,取消对该舱位的自动取样；此时,相应检测舱位工作指示灯显示为“人工切断”,自动循环检测将越过,不对该舱位进行取样检测.当该舱位压载水排空后,需要继续对该舱位进行检测时,请打开此舱位的取样进口阀,并再次按下控制柜面板上相应舱位的“人工切断”按钮,以恢复对该舱位的取样监测；此时,该舱位工作指示灯的“人工切断”指示熄灭.当系统循环取样切换至该舱位时,将自动先行吹扫该舱位取样管线,待排空取样管内水气、杂物后,进入正常取样模式,该舱位工作指示灯从“扫气”变为“取样”.
4.9 当需要对某些舱位进行持续监测时,可将工作模式开关选择为“手动取样”,通过“手动切换”按钮来人工切换至需要检测的舱位；此时,“手动取样”指示灯点亮,相应检测舱位工作指示灯显示为“取样”,显示屏持续显示当前测量点位的可燃气体浓度读数.如出现“管线故障”（手动时不具备自动吹扫功能）或者其他需要进行人工管线吹扫的情况时,可将工作模式开关选择为“手动扫气”,通过“手动切换”按钮来人工切换至需要进行扫气的舱位；此时,“手动扫气”指示灯点亮,相应检测舱位工作指示灯显示为“扫气”,完成后,再次将工作模式开关选择为“手动取样”,以完成取样监测功能.
4.10 系统通过双针压力表监测取样管线真空压力,如果某一舱位的真空压力过高,可以认为
该路取样管线堵塞或者该舱位压载水未完全排空,系统将执行自动吹扫,再次取样时,如果仍然检测到真空压力过高,“管线故障”指示灯闪烁,蜂鸣器鸣响,按下消音按钮后,蜂鸣器停止鸣响,“管线故障”指示灯变为常亮；如果某一舱位的真空压力过低,可以认为该路取样管线破损或真空泵故障,“管线故障”指示灯闪烁,蜂鸣器鸣响,按下消音按钮后,蜂鸣器停止鸣响,“管线故障”指示灯变为常亮；如果其他检测舱位再次管线堵塞情况,声光警报将再次出现；如果全部检测舱位管线正常,按下复位按钮后,“管线故障”指示灯熄灭.管线故障报警的舱位、时间信息的历史记录可在显示屏的相关页面查询、显示.出现“管线故障”指示时,系统将自动越过该舱位,进入下一舱位的检测,直到下一检测循环.
4.11 系统自动监测可燃气体传感器的工作状态,当出现传感器短路或者开路的情况,“传感器故障”指示灯闪烁,蜂鸣器鸣响,按下消音按钮后,蜂鸣器停止鸣响,“传感器故障”指示灯变为常亮；待故障排除后,按下复位按钮后,“传感器故障”指示灯熄灭.传感器故障报警的类别、时间信息的历史记录可在显示屏的相关页面查询、显示.
4.12 系统自动监测控制柜的电源供给状态,当主电源或者备用电源任一确失,“电源故障”指示灯闪烁,蜂鸣器鸣响,按下消音按钮后,蜂鸣器停止鸣响,“电源故障”指示灯变为常亮.当电源恢复供应后,“电源故障”指示灯自动熄灭.
4.13 系统参数可以在显示屏轻松修改,但为防止无关人员误操作,需要输入修改密码方能完成.
系统密码为“1111”.
4.14 标准气体的校验,可以通过按下“校验”按钮,将标准气接入柜内检测吸口端,验证系统的警报指示、传感器精度、真空取样泵切换动作等各项功能.

英语翻译4.8 当某些舱位作为压载使用后,请立即关闭相关舱位的取样进口阀,并按下控制柜面板上相应舱位的“人工切断”按钮,取消对该舱位的自动取样；此时,相应检测舱位工作指示灯显示
4.8 when after certain seats on a ship take the ballast use, please immediately close is related the seat on a ship the sample import valve, and presses down on the control cubicle kneading board the corresponding seat on a ship “the artificial cut-off” the button, cancels to this seat on a ship mechanical sampling; This time, examines the seat on a ship work indicating lamp demonstration is correspondingly “the artificial cut-off”, the autocycle examination will cross, does not carry on the sample examination to this seat on a ship. After this seat on a ship ballast water evacuation, needs to continue when carries on the examination to this seat on a ship, please do open this seat on a ship the sample import valve, and presses down on once more control cubicle kneading board the corresponding seat on a ship “the artificial cut-off” the button, restores to this seat on a ship sample monitor; This time, this seat on a ship work indicating lamp “artificial cut-off” instruction extinguishment. When systemic circulation sample cut to this seat on a ship, will be automatic blows in advance sweeps this seat on a ship sample pipeline, after treating in the evacuation pipe ore sampler the moisture, the sundry goods, enters the normal sample pattern, this seat on a ship work indicating lamp from “sweeps was mad that” becomes “the sample”.
4.9 when needs to carry on to certain seats on a ship monitors continually, may the working pattern switch choice be “the manual sample”, adopts “the manual cut” the button to come the manual switching to the seat on a ship which needs to examine; This time, “the manual sample” the indicating lamp lightens, examines the seat on a ship work indicating lamp demonstration is correspondingly “the sample”, the display monitor demonstrates the current measuring point position continually the flammable gas density reading. If presents “the pipeline breakdown” (manual time when does not have blows automatically sweeps function) or other needs carries on the situation which the artificial pipeline blows sweeps, may be “manual sweeps the working pattern switch choice is mad”, adopts “the manual cut” the button to come the manual switching to need to carry on sweeps the gas the seat on a ship; This time, “manual sweeps was mad that” the indicating lamp lightens, examines the seat on a ship work indicating lamp demonstration is correspondingly “sweeps is mad”, after completing, the working pattern switch choice will be once more “the manual sample”, completes the sample monitor function.
4.10 systems through cross-pointing pressure gauge monitor sample pipeline vacuum pressure, if some seat on a ship's vacuum pressure is excessively high, may think that the this group sample pipeline jamming or this seat on a ship ballast water has not evacuated completely, the system will carry out blows automatically sweeps, when resampling, if still examined the vacuum pressure to be excessively high, “the pipeline breakdown” the indicating lamp twinkle, the buzzer resounds, after pressing down the deafen button, the buzzer stops resounding, “the pipeline breakdown” the indicating lamp becomes is often bright; If some seat on a ship's vacuum hypotonia, may think that this group sample pipeline breakage or the vacuum pump breakdown, “the pipeline breakdown” the indicating lamp twinkle, the buzzer resounds, after pressing down the deafen button, the buzzer stops resounding, “the pipeline breakdown” the indicating lamp becomes is often bright; If other examine the seat on a ship once more pipeline jamming situation, the acousto-optic warning will appear once more; If examines the seat on a ship pipeline to be normal completely, after pressing down the reset button, “pipeline breakdown” indicating lamp extinguishment. The pipeline malfunction alert's seat on a ship, the time information's historic record may in display monitor's related page inquiry, the demonstration. When appearance “pipeline breakdown” instruction, the system will cross this seat on a ship automatically, enters the next seat on a ship the examination, until next examination circulation.
4.11 system automatic monitor flammable gas sensor's active status, when presents the sensor to short-circuit or the opening situation, “the sensor breakdown” the indicating lamp twinkle, the buzzer resounds, after pressing down the deafen button, the buzzer stops resounding, “the sensor breakdown” the indicating lamp becomes is often bright; After treating the trouble shooting, after pressing down the reset button, “sensor breakdown” indicating lamp extinguishment. The sensor malfunction alert's category, the time information's historic record may in display monitor's related page inquiry, the demonstration. the 4.12 system monitors control cubicle's power supply condition automatically, when the main power source or the emergency power supply any one loses firmly, “the power failure” the indicating lamp twinkle, the buzzer resounds, after pressing down the deafen button, the buzzer stops resounding, “the power failure” the indicating lamp becomes is often bright. After the power source resumes the supply, “the power failure” the indicating lamp extinguishes automatically.
the 4.13 system parameters may with ease revise in the display monitor, but to prevent the irrelevant personnel misoperation, needs to input the revision password side to be able to complete. the system password is “1111”.
the 4.14 standard gas's verification, may through press down “the verification” the button, enters in the cabinet the standard gas welding to examine the suction port end, the confirmation system's warning indication, the sensor precision, the vacuum sample pump cut movement and so on each function.

你还真客气 10分太多了```拿回去点拿回去点```

额的神阿！

4.8 when some accommodation to use as ballast, please accommodation for the immediate closure of the relevant import sampling valve, and press the corresponding control of counter space on the board o...

全部展开

4.8 when some accommodation to use as ballast, please accommodation for the immediate closure of the relevant import sampling valve, and press the corresponding control of counter space on the board of the "artificial cut off" button, the abolition of the automatic sampling of the class; at this time, the corresponding Detection of accommodation for the work of light appear as "artificial cut off," automatically cycle testing will be crossed, not the space to carry out sampling testing. When the class of ballast water emptying, the need to continue to test the class, please open this space import sampling valve, and once again press the control of the corresponding counter-board accommodation for the "artificial cut off" button to restore the Sampling and Monitoring of accommodation; at this time, the cabin light work of the "artificial cut off" the instructions went out. When the system switch to the sampling cycle of accommodation will automatically purge the first class sampling pipeline, to be emptying water vapor sampling tube, after the debris into the normal sampling mode, the indicator light work of accommodation from the "Scavenging" to " sampling. "
4.9 When the need for some space to carry out continuous monitoring, they can choose the mode switch to "manual sampling" by "manually switch" button to manually switch to the need for detection of accommodation; at this time, "Manual sampling" instruction lights lit, the corresponding indicator light detection work space shown as "sampling", the screen shows the current measurement of continuous point combustible gas concentration readings. Such as the "fault line" (when do not have the automatic manually purge function) or other need for artificial pipelines Purge of the situation, could be the work mode switch to choose to "manual scavenging" by "manually switch" button to manually switch to the need for scavenging of accommodation; at this time, "manual scavenging" light is lit, the corresponding indicator light detection work space shown as "Scavenging", after the completion of the work mode switch again to choose "Hands dynamic sampling "to complete the sampling monitoring.
4.10 pressure gauge monitoring system, through the double needle sampling pipeline vacuum pressure, if a class of vacuum pressure is too high, it could be considered
Sampling of the road or in the pipeline to plug accommodation ballast water has not been completely emptied, the system will automatically purge and, once again sampling, if the vacuum pressure is still detected too high, "fault line" light is flashing, buzzers sound, press the mute button, the buzzer to stop ringing, "fault line" light into Always; if a certain class of the vacuum pressure is too low, that the road can be damaged or vacuum sampling pipeline failure, "fault line" instruction lights flashing, buzzers sound, press the mute button, the buzzer to stop ringing, "fault line" light into Always; if other detection pipeline blockage of space again, sound and light warning will come up again; if All testing accommodation pipeline to normal, press the reset button, the "fault line" indicator goes out. Pipeline failure alarm of accommodation and time information to the history of the relevant page in the display inquiries, show. A "fault line" instruction, the system will automatically cross the space, into the next class of detection, until the next testing cycle.
4.11 automatically combustible gas sensor to monitor the work of state, when a sensor short circuit or open circuit, the "sensor failure" light blinking, buzzer sound, press the mute button, the buzzer to stop ringing, "sensor failure "light into Always; troubleshooting question, press the reset button, the" sensor failure "indicator goes out. The type of sensor fault alarm, the time history information can display the relevant page inquiries, show.
4.12 automatically monitor and control the power supply cabinet, and when the main power or standby power loss of any one indeed, "power failure" light blinking, buzzer sound, press the mute button, the buzzer to stop ringing, "Power Fault "light into Always. When the supply of power is restored, the "power failure" light automatically extinguished.
4.13 system parameters can easily modify the display, but has nothing to do in order to prevent misoperation staff, need to enter a password in order to complete the modifications.
System password to "1111."
4.14 standard calibration gas, you can press the "Check" button, the standard gas detection access inside suction side of the instructions to verify the alarm system, sensor accuracy, vacuum pump sampling various functions such as switch

收起